Purge Solutions TRYCLOPS X Purge Controller XP

Roll over image to zoom in Click on image to zoom

Purge Solutions TRYCLOPS X - Purge Controller XP

Simple to install & use
Highly reliable
Can monitor & control up to three purged enclosures
Exhaust vent(s) standard
Local & remote status alarms
Casing available in anodized aluminum or 316 stainless-steel
115 VAC up to 25 Amps or 230 VAC up to 12.5 Amps
All in One Unit

After the automatic dilution purge time has elapsed, the local green LED indicator will stop flashing and go into a continuous green state. Indicating that the monitored enclosure(s) pressure is being maintained above 0.30 inches of water column (0.75mbar) and enclosure exhaust port(s) is registering satisfactory flow. Up to 12.5 Amps of power will then be automatically applied by the TRYCLOPS X - Purge Controller, eliminating the need for an additional explosion proof enclosure with a solid-state relay.

The TRYCLOPS X - Purge Controller continuously compares the purge pressure inside the monitored electrical equipment enclosure(s) with respect to the atmospheric pressure surrounding the enclosure(s) preventing the ingress of flammable materials in the surrounding atmosphere from entering into the enclosure(s) as long as positive purge pressure and exhaust port(s) flow is maintained. If the enclosure(s) pressure should go below 0.30 inches of water column (0.75mbar) and / or exhaust port(s) flow stops the local LED indicator will go from steady state of green to a steady state of red, power will be disconnected from the unprotected monitored electrical equipment and if used a dry-contact alarm for either situation, will be sent to the remote point for monitoring.

Other features of the TRYCLOPS X - Purge Controller are a Maintenance Switch and Power Disconnect Bypass Switch. The Maintenance Switch is used when electrical equipment within the enclosure(s) being monitored by the TRYCLOPS X - Purge Controller requires electrical power for repair or maintenance. After the area surrounding the enclosure(s) has been tested and is known to be non-hazardous. The enclosure(s) can then be opened without protective purge pressure exposing the electronic equipment to its surrounding atmosphere. The TRYCLOPS X - Purge Controller's Maintenance Switch can then be put in maintenance mode and power will then be applied to the electrical equipment for repair or maintenance. During this time the local visual LED indicator will flash red and if used, the dry contact will send an alarm to its point of remote monitoring. When repair or maintenance has been completed, the electronics equipment's enclosure(s) door can then be closed and fastened. Purge pressure can then be restored to the enclosure(s) and if the purge pressure remains above 0.30 inches of water column (0.75mbar) and if there is satisfactory exhaust vent flow, the Maintenance Switch when turned to normal operation, instead of going through the dilution cycle, the electrical equipment's power will remain on.

The Power Disconnect Bypass Switch is used to override the disconnecting of power to the electrical equipment within the enclosure being monitored by the TRYCLOPS X - Purge Controller for installations where immediate loss of power would result in a more hazardous condition. Power to the electrical equipment within the enclosure being monitored by the TRYCLOPS X - Purge Controller shall be permitted to be continued for a short period of time if both audible and visual alarms are provided at a constantly attended location. During this time the local visual LED will be a steady state green and blink red.

The TRYCLOPS X - Purge Controller monitors the purge pressure and exhaust flow from up to three pressure and exhaust vent flow points, which is specified by the customer and built by the manufacture at time of purchase. The TRYCLOPS X - Purge Controller was specifically designed for use with analyzers, mounts in the general area of the enclosure(s) it will be monitoring and comes standard with a purge exhaust vent for each enclosure the TRYCLOPS X - Purge Controller will be monitoring.

The TRYCLOPS X - Purge Controller, is explosion proof (flameproof) comes in anodized aluminum or in 316 stainless steel. The TRYCLOPS X - Purge Controller comes with voltage options of 115 or 230 VAC able to control up to 12.5 Amps.

Get A Quote

Simple to install & use
Highly reliable
Can monitor & control up to three purged enclosures
Exhaust vent(s) standard
Local & remote status alarms
Casing available in anodized aluminum or 316 stainless-steel
115 VAC up to 25 Amps or 230 VAC up to 12.5 Amps
All in One Unit

Description
Technical Data
Resources
Approvals
Installation Video

Description

GET A QUOTE – Not available for purchase online. Please click the link to request a quote or call 281-336-9070.

The TRYCLOPS X – Purge Controller is a compact, intelligent solution designed to safeguard electrical enclosures in high-risk industrial environments. Developed by Purge Solutions, it enables standard equipment to operate safely in Class I Division 1 purge areas by eliminating explosive atmospheres and maintaining a safe internal pressure.

Ideal for petrochemical facilities, refineries, and chemical processing plants, the TRYCLOPS X supports critical safety and compliance goals. As a Type X purge system, it allows users to downgrade the internal classification of an enclosure to non-hazardous, significantly expanding equipment options while meeting strict safety standards.

The TRYCLOPS X – Purge Controller monitors purge pressure, exhaust vent flow, and controls electrical power and pre-dilution purge time for up to three (3) pressurized enclosures. Its local and remote indicators provide objective evidence of the presence of positive purge pressure and exhaust port flow. When an enclosure maintains pressure of at least 0.30 inches of water column (0.75 mbar) and satisfactory vent flow, a flashing green LED signals safe conditions. A dilution purge cycle, programmable from 1 to 99 minutes, can then begin. Once complete, the TRYCLOPS automatically energizes the internal equipment.

Certified to NFPA 496, ATEX, IECEx, and Class I, Division 1 standards, the TRYCLOPS X includes redundant sensors and will trigger alarms or shutdowns in unsafe conditions. RS-485 Modbus communication supports real-time monitoring. Its compact design fits tight panels and supports new and retrofit installations. The TRYCLOPS X is engineered for long-term reliability and safety without adding unnecessary system complexity.

Purge gas inlet kits are available with each controller. Contact us at 281-978-2040 for further details.

We are an authorized Purge Solutions distributor shipping worldwide.

Frequently Asked Questions

What is Type X purge?

A Type X purge system protects enclosures in Class I, Division 1 or Zone 1 hazardous areas. It uses clean instrument air or inert gas to remove flammable vapors, then maintains positive pressure inside the enclosure. This isolates electrical components and prevents ignition of explosive gases.

The purge process downgrades the enclosure's classification from Division 1 to unclassified. This enables the use of general-purpose equipment in environments that would otherwise require expensive explosion-proof solutions. Type X purging is essential for safety and flexibility.

What is the difference between X Purge and Z Purge?

The difference lies in the hazard level and application. Type X is used in Division 1 or Zone 1 areas with constant or likely explosive risks. It reduces the enclosure’s classification from Division 1 to unclassified and is suited for non-rated equipment.

Type Z purge systems are used in Division 2 or Zone 2, where explosive conditions are less likely. They downgrade the classification from Division 2 to unclassified. Type X provides a higher level of protection than Type Z and is used in more critical areas.

Why should I trust the TRYCLOPS X Purge Controller?

The TRYCLOPS X is a third-generation controller trusted in critical hazardous applications. Built by Purge Solutions, it features redundant sensors, RS-485 Modbus connectivity, and independent control of up to three enclosures. It’s engineered for long-term reliability.

Certified to NFPA 496, ATEX, IECEx, and Class I, Division 1, the TRYCLOPS X meets global safety standards. Its compact design allows for easy installation in tight spaces. With proven field performance, it delivers dependable protection in demanding environments.

For help selecting the right purge and pressurization system, contact Exloc Instruments today.

Technical Data

Overall Unit Dimensions	10.3” (261.6mm) wide x 10.4” (264.7mm) tall x 8.3” (211.8mm) deep
Unit Weight	TRYCLOPS X – Purge Controller, XP Version, Anodized Aluminum = 29.72 lbs. (13.48 kg) TRYCLOPS X – Purge Controller, XP Version, 316 Stainless Steel = 70.07 lbs. (31.78 kg)
Operating Temperature Range	- 40ºF to 150ºF (-40ºC to 65ºC)
Minimum Overpressure Switch Settings	0.30 inch H2O (0.75 mbar) for gas hazardous locations 0.50 inch H2O (1.25 mbar) for dust hazardous locations
Power Control Capability	115 VAC up to 25 Amps RMS continuous over specified voltage ranges 230 VAC up to 12.5 Amps RMS continuous over specified voltage ranges
Power Input / Consumption	2 watts max
Ingress Protection	Anodized Aluminum and 316 Stainless Steel = NEMA 4X (IP66)
Voltage	115 VAC model (85 VAC to 160 VAC), 47 to 63 Hz. 230 VAC model (130 VAC to 265 VAC), 47 to 63 Hz.
Alarm Dry Contact Maximum Continuous Load Rating	Contact open on alarm (NO) Contact closed on alarm (NC) 150 mA rms AC 150 mA DC
Standard Hardware	Exhaust Vent for each enclosure the TRYCLOPS X – Purge Controller will be monitoring and USB with documentation.

Resources

Approvals

ATEX and IECEx
II 2 G Ex e mb ib [px] IIC T4 Gb for Zone 1 gas hazardous areas
II 2 D Ex tb IIIC T119°C Db IP66 for Zone 21 dust hazardous areas
ANSI / ISA 12.4, CEC, NEC and NFPA 496
Class I, Division 1, Group B,C,&D, T4 for gas hazardous areas
Class II, Division 1, Group E,F&G, T4 for dust hazardous areas
Certified to an Ambient Temperature Range of - 40ºF (- 40ºC) <Tamb< + 149ºF (+ 65ºC)
CE Marked